AGS 3502 ICE Wax-based - Cold conditions

Article number: 3502ICE

A water-carried all-weather long-term protection, formulated for most types of surfaces. May be used below 0°C. Provides extra strong protection against spray paint, marker/felt-tip pens and mechanical damage. Protects against airborne pollution and moisture for a minimum of 7 years. Permeable and allows protected surface to breath. Correctly applied, life expectancy against graffiti
is approximately 7 years. Prevents graffiti from penetrating into substrate. A so-called sacrificial coating, which means that surface must be re-protected following graffiti removal. AGS 3502 ICE is readily biodegradable.


Application instructions

Clean off both graffiti and other contamination, such as traffic dirt, wax, oil and paint residue etc. from substrate. Mask and protect windows in a suitable manner. Ideal temperature for external application should be between 0-35°C. Minimum temperature is -3°C. Relative humidity must not exceed 95%. Note! Fresh concrete has to cure for at least 28 days before protection.

Exterior protection
Shake or stir product well prior to use. AGS 3502 ICE can be applied with a low-pressure sprayer or airless spray gun. The protection is applied 2-3 times. Note! Allow some drying between applications. AGS 3502 ICE can be applied to a damp, but not wet surface. Runs and/or excessive application can easily be washed off with water, following completion of work.

Interior protection
Painted substrate can be protected using a squeegee brush, roller or with low-pressure sprayer in combination with a squeegee. The protection is applied three times.

Exterior graffiti removal
Method 1 – Normal substrate
Remove graffiti with hot water and high-pressure (90°C & 90-150 bar / 1300-2175 PSI). In difficult cases, AGS graffiti removers are used in conventional manner. Re-protect cleaned area.

Method 2 – Sensitive substrate
Apply AGS 3505 with a low-pressure sprayer. Allow a few minutes for the solvent remover to act and then rinse off with hot water (60-90°C & 60-80 bar/870-1160 PSI). The method is most suitable when substrate is brittle. Any graffiti left on the surface can be removed with AGS 3505 on a cloth. The cleaned area should be wiped with a cloth and water. Re-protect cleaned area.

Interior graffiti removal
Painted substrate:
Dampen the area with AGS 3505 and wipe off graffiti with white nylon clothe or rag. If possible use high-pressure hot water and wet-vac machines.

Porous substrate:
Rinse off with hot water and wet-vac.

Re-protection of cleaned surface
When removing graffiti, the protective coating is also normally removed. Re-protect 2-3 times with AGS 3502 ICE.

Use in concentrated form.

Varies depending upon type of surface material. Its porosity and capillary ability etc.


  • Concrete, brick or similar, a total for 3 layers will be 0,25-0,3 ltr/m².
  • Sandstone, plaster or other soft absorbent surfaces, a total for 3-4 layers will be 0,3-0,4 ltr/m².

The protected surface will be water- and graffiti-resistant after 2 hours and dry after 4 hours. Ultimate protective effect will be achieved after 72 hours.

Appearance on surface
Transparent, mostly invisible dependent on type of surface. UV-resistant. Weather-, water-, and graffiti – resistant. Note! Some building materials can darken or become shiny.

Store frost-free in closed original container.

Shelf life
Approximately 12 months in unopened container.

Use protective clothing and gloves.


Technical data

  • White water-carried dispersion.
  • Packaging: 5 or 25 litre plastic jerricans.
  • Density: 0,98 kg/litre.
  • pH-value approx. 8.
  • Contains wax, ethanol, isopropanol, alcohols ethoxylated.

Not classified

Not classified as dangerous goods according to ADR.
For more information, see MSDS.

Contact us